Tidal power

Tidal power is a means of electricity generation achieved by capturing the energy contained in moving water mass due to tides. Two types of tidal energy can be extracted: kinetic energy of currents arising between ebbing and surging tides and potential energy from the difference in height (or head) between high and low tides. The former method - generating energy from tidal currents - is considered much more feasible today than building ocean-based dams or barrages, and many coastal sites worldwide are being examined for their suitability to produce tidal (current) energy.

The extraction of potential energy involves building a barrage and creating a tidal lagoon. The barrage traps a water level inside a basin. Head is created when the water level outside of the basin or lagoon changes relative to the water level inside. The head is used to drive turbines. In any design this leads to a decrease of tidal range inside the basin or lagoon, implying a reduced transfer of water between the basin and the sea. This reduced transfer of water accounts for the energy produced by the scheme.

Tidal power is classified as a renewable energy source, because tides are caused by the orbital mechanics of the solar system and are considered inexhaustible within a human timeframe. The root source of the energy comes from the slow deceleration of the Earth's rotation. The Moon gains energy from this interaction and is slowly receding from the Earth. Tidal power has great potential for future power and electricity generation because of the total amount of energy contained in this rotation. Tidal power is reliably predictable (unlike wind energy and solar power).

The efficiency of tidal power generation in ocean dams largely depends on the amplitude of the tidal swell, which can be up to 10 m (33 ft) where the periodic tidal waves funnel into rivers and fjords. Amplitudes of up to 17 m (56 ft) occur for example in the Bay of Fundy, where tidal resonance amplifies the tidal waves.

As with wind power, selection of location is critical for a tidal power generator. The potential energy contained in a volume of water is

E = xMg

where x is the height of the tide, M is the mass of water and g is the acceleration due to gravity. Therefore, a tidal energy generator must be placed in a location with very high-amplitude tides. Suitable locations are found in the former USSR, USA, Canada, Australia, Korea, the UK and other countries (see below).

Several smaller tidal power plants have recently started generating electricity in Norway. They all exploit the strong periodic tidal currents in narrow fjords using sub-surface water turbines.

Barrages

Barrages are used to close off a basin for trapping a water level inside them. The basic elements of a barrage are caissons, embankments, sluices, turbines and ship locks. Sluices, turbines and ship locks are housed in caisson (very large concrete blocks). Embankments seal a basin where it is not sealed by caissons.

The sluice gates applicable to tidal power are the flap gate, vertical rising gate, radial gate and rising sector.

Turbines

The turbines used in this application are variations of the Kaplan turbine, which have an ultra fast specific speed that allows them to operate with very low heads. They may also have variable pitched blades to further improve efficiency for varying tides and flow rates.

Installed capacity

The total rated capacity (in MW) of the turbines is optimised for each barrage. At a low relative installed capacity, a small amount of energy will be produced, but production will last for a long period of time. At maximum installed capacity, the basin will drain very quickly in every cycle, producing the maximum possible energy, at a very high rate, but only for a short period of time, making it difficult to absorb into the grid. A fast decrease in water level could also have negative effects on the environment.

The addition of capacity to a turbine follows the law of diminishing returns: for each additional MW, less extra energy will be produced.

Modes of operation

Ebb generation

The basin is filled through the sluices and freewheeling turbines until high tide. Then the sluice gates and turbine gates are closed. They are kept closed until the sea level falls to create sufficient head across the barrage and the turbines generate until the head is again low. Then the sluices are opened, turbines disconnected and the basin is filled again. The cycle repeats itself. Ebb generation (also known as outflow generation) takes its name because generation occurs as the tide ebbs.

Flood generation

The basin is emptied through the sluices and turbines generate at tide flood. This is generally much less efficient than ebb generation, because the volume contained in the upper half of the basin (which is where ebb generation operates) is greater than the volume of the lower half (the domain of flood generation). This is compounded by the fact that there is usually a river flowing into the basin, filling the basin as the tide rises and making the difference in levels between the basin side and the sea side of the barrage (and therefore the available potential energy) less than it would otherwise be. This is not a problem with the lagoon model.

Two-way generation

Generation occurs both as the tide ebbs and floods. This mode is only comparable to ebb generation at spring tides, and in general is less efficient. Turbines designed to operate in both directions are less efficient.

Pumping

Turbines can be powered in reverse by excess energy in the grid to increase the water level in the basin at high tide (for ebb generation and two-way generation). This energy is returned during generation.

Two-basin schemes

With two basins, one is filled at high tide and the other is emptied at low tide. Turbines are placed between the basins. Two-basin schemes offer advantages over normal schemes in that generation time can be adjusted with high flexibility and it is also possible to generate almost continuously. In normal estuarine situations, however, two-basin schemes are very expensive to construct due to the cost of the extra length of barrage. There are some favourable geographies, however, which are well suited to this type of scheme.

Tom and Wendy

Tom and Wendy are world renowned Tidal and Wave Energy experts. The are extremely fantastic and are often helped out by their friend, the 'Random Clueless Person.'

Marine current turbines

Various designs are proposed to extract kinetic energy from tidal currents. A generic current turbine will be rotated by water currents in the same way as wind power generators are rotated by air currents. The scheme would convert the currents' energy into electricity, slowing the currents down.

An experimental tidal power station was installed in Kvalsundet, south of Hammerfest, Norway, and became operational in November 2003. The installed tidal power turbine generates a maximum of 300 kW at a maximum speed of the current of 2.5 m/s. More information can be found at http://www.e-tidevannsenergi.com/index.html

Intermittent nature of power output

Tidal power schemes do not produce energy 24 hours a day. A conventional design, in any mode of operation, would produce power for 6 to 12 hours in every 24 and will not produce power at other times. As the tidal cycle is based on the period of revolution of the Moon (24.8 hours) and the demand for electricity is based on the period of revolution of the Sun (24 hours), the energy production cycle will not always be in phase with the demand cycle. This causes problems for the electric power transmission grid, as capacity with short starting and stopping times (such as hydropower or gas fired power plants) will have to be available to alternate power production with the tidal power scheme.

Mathematical modelling

In mathematical modelling of a scheme design, the basin is broken into segments, each maintaining its own set of variables. Time is advanced in steps. Every step, neighbouring segments influence each other and variables are updated.

The simplest type of model is the flat estuary model, in which the whole basin is represented by one segment. The surface of the basin is assumed to be flat, hence the name. This model gives rough results and is used to compare many designs at the start of the design process.

In these models, the basin is broken into large segments (1D), squares (2D) or cubes (3D). The complexity and accuracy increases with dimension.

Mathematical modelling produces quantitative information for a range of parameters, including:

• Water levels (during operation, construction, extreme conditions, etc.)
• Currents
• Waves
• Power output
• Turbidity
• Salinity
• Sediment movements

Physical modelling

Small-scale physical representations of a tidal power scheme can be built. These have to be large to be accurate. Physical models are very expensive and are used only in critical projects.

Environmental impact

Local environmental impact

The placement of a barrage into an estuary has a considerable effect on the water inside the basin and on the fish. Lagoons, on the other hand, could be used for fish or lobster farming, adding to their economic viability.

Turbidity

Turbidity (the amount of matter in suspense in the water) decreases as a result of smaller volume of water being exchanged between the basin and the sea. This lets light from the Sun to penetrate the water further, improving conditions for the phytoplankton. The changes propagate up the food chain, causing a general change in the ecosystem.

Salinity

Again as a result of less water exchange with the sea, the average salinity inside the basin decreases, also affecting the ecosystem. Again, lagoons do not suffer from this problem.

Sediment movements

Estuaries often have high volume of sediments moving through them, from the rivers to the sea. The introduction of a barrage into an estuary may result in sediment accumulation within the barrage, affecting the ecosystem and also the operation of the barrage.

Pollutants

Once again, as a result of reduced volume, the pollutants accumulating in the basin will be less efficiently dispersed. Their concentrations will increase. For biodegradable pollutants, such as sewage, an increase in concentration is likely to lead to increased bacteria growth in the basin, having impacts on the health of the human community and the ecosystem.

The concentrations of conservative pollutants will also increase.

Fish

Fish may move through sluices safely, but when these are closed, fish will seek out turbines and attempt to swim through them. Also, some fish will be unable to escape the water speed near a turbine and will be sucked through. Even with the most fish-friendly turbine design, fish mortality per pass is approximately 15% (from pressure drop, contact with blades, cavitation, etc.). This can be acceptable for a spawning run, but is devastating for local fish who pass in and out of the basin on a daily basis. Alternative passage technologies ( fish ladders, fish lifts, etc.) have so far failed to solve this problem for tidal barrages, either offering extremely expensive solutions, or ones which are used by a small fraction of fish only. Research in sonic guidance of fish is ongoing.

Global environmental impact

A tidal power scheme is a long-term source of electricity. The Severn Barrage, when built, is projected to save a million tons of coal per year of operation. This decreases the output of greenhouse gases into the atmosphere. More importantly, as the fossil fuel resource is likely to be eliminated by the end of the twenty-first century, tidal power is one of the alternative source of energy that will need to be developed to satisfy the human demand for energy.

Economic considerations

Tidal power schemes have a very high capital cost and a very low running cost. As a result, a tidal power scheme will not produce returns for decades after it is built, and investors are not likely to participate in such projects. Governments may be able to finance tidal power, but many are unwilling to do so also due to the extremely long time before returns and the huge irreversible commitment.

Resource around the world

Operating tidal power schemes

• The first tidal power station was built over a period of 6 years from 1960 to 1966 at La Rance, France ( [1]). It has 240MW installed capacity.
• The first (and only) tidal power site in North America is the Annapolis Royal Generating Station, which opened in 1984 on an inlet of the Bay of Fundy [2]. It has 20MW installed capacity.
• A small project was built by the Soviet Union at Kislaya Guba on the White Sea. It has 0.5MW installed capacity.
• China has apparently developed several small tidal power projects and one large facility in Jiangxia.
• China is also developing a tidal lagoon ([near the mouth of the Yalu] [3])
• Scotland has committed to having 18% of its power from green sources by 2010, including 10% from a tidal generator. The British government says this will replace one huge fossil fueled power station. [4]

Tidal power schemes being considered

In the table, '-' indicates missing information, '?' indicates information which has not been decided.car

Country	Place	Mean tidal range (m)	Area of basin (km2)	Installed capacity (MW)
Argentina	San Jose	5.9	-	6800
Australia	Secure Bay	10.9	-	?
Canada	Cobequid	12.4	240	5338
	Cumberland	10.9	90	1400
	Shepody	10.0	115	1800
India	Kutch	5.3	170	900
	Cambay	6.8	1970	7000
Korea	Garolim	4.7	100	480
	Cheonsu	4.5	-	-
Mexico	Rio Colorado	6-7	-	?
	Tiburon	-	-	?
United Kingdom	Severn	7.0	520	8640
	Mersey	6.5	61	700
	Wyre	6.0	5.8	47
	Conwy	5.2	5.5	33
United States	Passamaquoddy Bay	5.5	-	?
	Knik Arm	7.5	-	2900
	Turnagain Arm	7.5	-	6500
Russia	Mezen	9.1	2300	15000
	Tugur	-	-	10000 or 7000
	Penzhinskaya Bay	6.0	-	50000